Code No. 80120-AN202
*Discontinued.
"Not just for lowering the vehicle height." "Super Low Stance Model" for reliable driving performance.
The model in the photo is HFC26
Application
Engine | MR20DD-SM23 |
---|---|
Model Year | 12/08 - 16/08 |
Remarks | *Please set within 3 steps to the negative of the factory setting for the front chamber adjustment. |
Specification
FRONT | REAR | |
---|---|---|
Damping force adjustment | 30 steps | 30 steps |
Base valve | - | - |
Height adjustable lower bracket | ○ | ○ |
Upper mount | Spherical bearing | Stock |
Inverted/Normal type | Inverted | Normal |
Damper/Spring layout | Coilover | Separated |
Spring rate change at factory | Possible | Impossible |
Damping force adjustment with wire | - | - |
Helper spring (Spring rate N/mm) | ○ ( 4.7 ) | - |
Factory *2 | Test data | Adjustable range High - Low *3 |
Drivable range High - Low *4 |
||
---|---|---|---|---|---|
FRONT | Ride height *1 | 645 | 645 | 645 ~ 618 | 645 ~ 618 |
Against stock | -56 | -56 | -56 ~ -83 | -56 ~ -83 | |
REAR | Ride height *1 | 658 | 649 | 658 ~ 616 | 658 ~ 639 |
Against stock | -50 | -59 | -50 ~ -92 | -50 ~ -69 |
*1. Height from road surface to fender arch.
*2. Height at factory is the data tested at HKS with the setting of Full Kit. (HKS' recommended setting.)
*3. Adjustable range (However, the lowest value may not be road legal.
Even within the adjustable range, car body, arm etc. may contact. In such case, it will be hard to drive.
Damper oil leakage or any other problems caused by low ride height setting from the factory setting will void the warranty of the product.)
*4. Drivable range that there is no contact of car body or arms etc. (However, change of tire/wheel size may cause a problem.)
Caution). Actual data depends on each vehicle.
Kit information
Spring of Full Kit
F | R | |
---|---|---|
Spring rate N/mm(kgf/mm) | 118 ( 12 ) | 118 ( 12 ) |
Free height (mm) | 170 | - |
Spring type | Straight | Special shape |
Recommended range to change spring rate N/mm(kgf/mm) | ±20 (2 ) | - |
Specification of damper
F | R | |
---|---|---|
Damping force (Rebound/Damping)N* | 932 / 304 | 696 / 275 |
Default position of dial | 15 | 15 |
Remaining damper stroke (Rebound/Damping)mm | 41 / 46 | 48 / 58 |
* The value of the damping force is at piston speed of 0.1m/sec.
Setting data
F | R | |||||||
---|---|---|---|---|---|---|---|---|
Default | Test | Drivable limit High * |
Drivable limit Low * |
Default | Test | Drivable limit High * |
Drivable limit Low * |
|
Length of case (mm) |
320 | ← | 320 | 306 | 353 | 347 | 353 | 336 |
Spring Set length(mm) |
204 | ← | 204 | 223 | - | - | - | - |
Length to ride hight adjuster (mm) |
33 | ← | 33 | 0 | 54 | 46 | 54 | 36 |
Lever ratio | 1.02 | 1.35(spg) , 0.90(dmp) |
* Refer to the above explanation *3 of ride height information for drivable high and low limitations.
Test vehicle information
F | R | ||
---|---|---|---|
Vehicle weight kg | 983 (950) | 752 (710) | |
Tire size (Air pressure) kPa | 195 / 60 - 16 ( 280 ) | 195 / 60 - 16 ( 280 ) | |
Wheel size | 6.0 JJ × 16 inset 45 | 6.0 JJ × 16 inset 45 | |
Alignment (Toe/Camber) |
Test data | in 0 mm / -2°00' | in 5.1 mm / -1°42' |
Standard value | in 0.5 ~ 2.5 mm / -1°08' ~ 0°22' | out 0.1 ~ in 7.9 mm / -1°55' ~ -0°55' |
* Test data at HKS.
Parts List * It may be changed without prior notice.
Point
・We have set the spring rate high compare to other vehicle's S-style X because it has smaller clearance between the tire and body so that it will have less vehicle movement.
・Adjustable chamber pillow upper is used for front upper mount.
・Please set within 3 steps to the negative of the factory setting for the front chamber adjustment. If you set it more than that it will interfere with brake hose bracket and brake tube and it will be very dangerous.
・You might feel the vibration depending on the vehicle's front height.
・It might interfere with the fender and the tire for rear case length of less than 336mm.
・Recommendation of tested dial setting: front:15, rear:15
・To not to interfere with tire in such as rear fender modification, the maximum rear case damper length is 326mm. Torsion beam and brake hose is the limit.
[ CLOSE ]