S-style L 2018 LANDY
Explanation of the product Application chart

LANDY SHC26
S-style L 2018 Code No. 80130-AN202
 
 


▲The above photo is an item for E51.

Pre-load Valve System & M4P Deliver Ultimate Elasticity Ideal for "Low-stance Enthusiasts"



Application   Specification
Engine MR20DD-SM23
Model Year 12/08 - 
Remarks  
 
  FRONT REAR
Damping force adjustment 30 steps 30 steps
Base valve - -
Height adjustable lower bracket
Upper mount Rubber Stock
Inverted/Normal type Inverted Normal
Damper/Spring layout Coilover Separated
Spring rate change at factory Possible Impossible
Damping force adjustment with wire - -
Helper spring
(Spring rate N/mm)
- -


Ride Height mm
  Factory *2 Test data Adjustable range
High - Low *3
Drivable range
High - Low *4
FRONT Ride height *1 655 664 ~ 632 664 ~ 632
Against stock -46 -37 ~ -69 -37 ~ -69
REAR Ride height *1 677 697 ~ 651 697 ~ 651
Against stock -31 -11 ~ -57 -11 ~ -57
*1. Height from road surface to fender arch.
*2. Height at factory is the data tested at HKS with the setting of Full Kit. (HKS' recommended setting.)
*3. Adjustable range (However, the lowest value may not be road legal.
Even within the adjustable range, car body, arm etc. may contact. In such case, it will be hard to drive.
Damper oil leakage or any other problems caused by low ride height setting from the factory setting will void the warranty of the product.)
*4. Drivable range that there is no contact of car body or arms etc. (However, change of tire/wheel size may cause a problem.)
Caution). Actual data depends on each vehicle.


Kit information
Spring of Full Kit
  F R
Spring rate N/mm(kgf/mm) 49 ( 5 ) 71 ( 7.2 )
Free height (mm) 220 -
Spring type Straight Barrel type Special shape
Recommended range to change spring rate N/mm(kgf/mm) ±10 (1 ) -
Specification of damper
  F R
Damping force (Rebound/Damping)N* 574 / 187 250 / 142
Default position of dial 15 15
Remaining damper stroke (Rebound/Damping)mm 64 / 52 78 / 81
* The value of the damping force is at piston speed of 0.1m/sec.
Setting data
  F R
Default Test Drivable limit
High *
Drivable limit
Low *
Default Test Drivable limit
High *
Drivable limit
Low *
Length of
case (mm)
330 339 328 340 344 362 344
Spring
Set length(mm)
195 195 216 - - - -
Length to ride hight
adjuster (mm)
44 53 21 37 54 15
Lever ratio 1.02 1.22(spg) , 0.91(dmp)
* Refer to the above explanation *3 of ride height information for drivable high and low limitations.


Test vehicle information
  F R
Vehicle weight kg 983 752
Tire size (Air pressure) kPa 195 / 60 - 16 ( 280 ) 195 / 60 - 16 ( 280 )
Wheel size 6.0 JJ × 16 inset 45 6.0 JJ × 16 inset 45
Alignment
(Toe/Camber)
Test data in 0 mm / -0°30' in 5.1 mm / -1°48'
Standard value in 0.5~2.5 mm / -1°08' ~ 0°22' out 0.1~in 7.9 mm / -1°55' ~ -0°55'
* Test data at HKS.


Parts List * It may be changed without prior notice.


Point
・With this product, the floating feeling and vehicle body roll are reduced to deliver stable driving feeling that enables a driver to enjoy driving.
・L=250 spring for the front side was selected to provide better ride comfort. Replacing with a shorter spring enables to increase the vehicle height lowering range.
・Recommended Dial Position at the Test: Front – 12 / Rear - 13
・If the front case length is extended to the upper limit or larger, the lower arm comes in contact with the stabilizer at full rebound.
・For the rear side, even with factory wheels (BRIDGESTONE/ECOPIA EP150), the tire comes in contact with the fender due to the limit of vehicle side’s arm.
 
※To install this product to HFC26, adjust the rear case length to 344mm or longer from 340mm before installation.
 
 
 
 


[ CLOSE ]

 

 

HKS