Code No. 80230-AT001
*Discontinued.
The new Max IV sporty suspension. Awesome sporty drive with great control and comfortable ride in the street.
The model in the photo is ZN6.
Application
Engine | FA20 |
---|---|
Model Year | 12/04 - 21/10 |
Remarks | Applied E, GT"Limited", Manual transmission |
Specification
FRONT | REAR | |
---|---|---|
Damping force adjustment | 30 steps | 30 steps |
Base valve | - | - |
Height adjustable lower bracket | ○ | ○ |
Upper mount | Spherical bearing | Rubber |
Inverted/Normal type | Inverted | Normal |
Damper/Spring layout | Coilover | Coilover |
Spring rate change at factory | Possible | Possible |
Damping force adjustment with wire | - | - |
Helper spring (Spring rate N/mm) | - | ○ ( 4.7 ) |
Factory *2 | Test data | Adjustable range High - Low *3 |
Drivable range High - Low *4 |
||
---|---|---|---|---|---|
FRONT | Ride height *1 | 654 | 642 | 670 ~ 610 | 670 ~ 620 |
Against stock | -16 | -28 | 0 ~ -60 | 0 ~ -50 | |
REAR | Ride height *1 | 657 | 645 | 671 ~ 592 ※5 | 671 ~ 596 |
Against stock | -14 | -26 | 0 ~ -79 ※5 | 0 ~ -75 |
*1. Height from road surface to fender arch.
*2. Height at factory is the data tested at HKS with the setting of Full Kit. (HKS' recommended setting.)
*3. Adjustable range (However, the lowest value may not be road legal.
Even within the adjustable range, car body, arm etc. may contact. In such case, it will be hard to drive.
Damper oil leakage or any other problems caused by low ride height setting from the factory setting will void the warranty of the product.)
*4. Drivable range that there is no contact of car body or arms etc. (However, change of tire/wheel size may cause a problem.)
Caution). Actual data depends on each vehicle.
Kit information
Spring of Full Kit
F | R | |
---|---|---|
Spring rate N/mm(kgf/mm) | 59 ( 6 ) | 38 ( 4 ) |
Free height (mm) | 170 | 170 |
Spring type | Straight | Straight |
Recommended range to change spring rate N/mm(kgf/mm) | ±20 ( 2 ) | ±20 ( 2 ) |
Specification of damper
F | R | |
---|---|---|
Damping force (Rebound/Damping)N* | 900 / 300 | 720 / 150 |
Default position of dial | 15 | 15 |
Remaining damper stroke (Rebound/Damping)mm | 41 / 46 | 53 / 47 |
* The value of the damping force is at piston speed of 0.1m/sec.
Setting data
F | R | |||||||
---|---|---|---|---|---|---|---|---|
Default | Test | Drivable limit High * |
Drivable limit Low * |
Default | Test | Drivable limit High * |
Drivable limit Low * |
|
Length of case (mm) |
230 | 220 | 245 | 204 | 265 | 254 | 276 | 234 |
Spring Set length(mm) |
164 | ← | 164 | 170 | 189 | ← | 189 | 206 |
Length to ride hight adjuster (mm) |
47 | 37 | 62 | 15 | 51 | 40 | 62 | 3 |
Lever ratio | 1.06 | 1.28 |
* Refer to the above explanation *3 of ride height information for drivable high and low limitations.
Test vehicle information
F | R | ||
---|---|---|---|
Vehicle weight kg | - (690) | - (550) | |
Tire size (Air pressure) kPa | 215 / 45 - 17 ( 240 ) | 215 / 45 - 17 ( 240 ) | |
Wheel size | 7.0 JJ × 17 off +48 | 7.0 JJ × 17 off +48 | |
Alignment (Toe/Camber) |
Test data | 0 mm / -1°12' | IN 1 mm / -2°24' |
Standard value | 0 ± 3 mm / 0°00' ± 45' | IN 2 ± 3 mm / -1°12' ± 45' |
* Test data at HKS.
Parts List * It may be changed without prior notice.
Point
This is the street version damper for 86/BRZ.
Although this is a product designed for comfort and stylish appearance it is able to hold its own with regards to road performance. 18 inch tires were chosen for settings.
This product is recommended to those who would use the vehicle daily and look for better ride comfort as much as possible for both drivers and passengers and who want to reduce arch gap or lower the vehicles' height. This damper has been developed to provide high ride quality through its supple yet stable setup. Once out at the race track, a twist of the adjustment dials can provide the performance necessary to enjoy the circuit.
Max 4 dampers utilize analysis data and perform tests on each vehicle to determine not just spring and damper rate, but also front/rear balance and stroke for people to enjoy this product safely. The concept is to try and see things from the viewpoint of the user as much as possible.
This product has many revised and newly made internal parts and includes stabilizer to achieve high levels of comfort handling and low stance without compromising.
In refining the low speed dampening, which is the key to ride comfort and handling, also the mid to high speed dampening properties, a new needle has been developed. Improved low speed dampening gives stable dampening which allows for the supple yet stable ride. It has also allowed the mid/high speed dampening to be cut which has increased performance over bumps and ridges in the road. The adjustment dial operation has been revised to allow oil to flow better to prevent the dial from locking up at under the dial 10.
●Slitting a part of rear interior is required in order to install the rear adjustment dial.
[ CLOSE ]