S-style C 2018 ELGRAND
Explanation of the product Application chart

ELGRAND MNE51
S-style C 2018 Code No. 80110-AN202
 
 


▲The above photo is an item for TC24.

Masterpiece of HKS "S-style" series! For the Best & Firm Ride!!



Application   Specification
Engine VQ25DE
Model Year 04/08 - 10/07
Remarks Highwayster 4WD
 
  FRONT REAR
Damping force adjustment - -
Base valve - -
Height adjustable lower bracket
Upper mount Rubber Stock
Inverted/Normal type Inverted Normal
Damper/Spring layout Coilover Separated
Spring rate change at factory Possible Impossible
Damping force adjustment with wire - -
Helper spring
(Spring rate N/mm)
- -


Ride Height mm
  Factory *2 Test data Adjustable range
High - Low *3
Drivable range
High - Low *4
FRONT Ride height *1 669 681 696 ~ 656 696 ~ 656
Against stock -47 -35 -20 ~ -60 -20 ~ -60
REAR Ride height *1 667 682 703 ~ 663 703 ~ 663
Against stock -51 -36 -15 ~ -55 -15 ~ -55
*1. Height from road surface to fender arch.
*2. Height at factory is the data tested at HKS with the setting of Full Kit. (HKS' recommended setting.)
*3. Adjustable range (However, the lowest value may not be road legal.
Even within the adjustable range, car body, arm etc. may contact. In such case, it will be hard to drive.
Damper oil leakage or any other problems caused by low ride height setting from the factory setting will void the warranty of the product.)
*4. Drivable range that there is no contact of car body or arms etc. (However, change of tire/wheel size may cause a problem.)
Caution). Actual data depends on each vehicle.


Kit information
Spring of Full Kit
  F R
Spring rate N/mm(kgf/mm) 69 ( 7 ) 73 ( 7.35 )
Free height (mm) 220 -
Spring type Straight Barrel type Special shape
Recommended range to change spring rate N/mm(kgf/mm) ±10 ( 1 ) -
Specification of damper
  F R
Damping force (Rebound/Damping)N* 892 / 387 775 / 490
Default position of dial - -
Remaining damper stroke (Rebound/Damping)mm 54/ 53 40/ 55
* The value of the damping force is at piston speed of 0.1m/sec.
Setting data
  F R
Default Test Drivable limit
High *
Drivable limit
Low *
Default Test Drivable limit
High *
Drivable limit
Low *
Length of
case (mm)
369 369 382 360 250 250 271 250
Spring
Set length(mm)
217 206 198 219 - - - -
Length to ride hight
adjuster (mm)
44 55 68 33 33 44 58 30
Lever ratio 1.18 1.45(spg) , 1.65(dmp)
* Refer to the above explanation *3 of ride height information for drivable high and low limitations.


Test vehicle information
  F R
Vehicle weight kg - -
Tire size (Air pressure) kPa 245 / 35 - 20 ( 300 ) 245 / 35 - 20 ( 300 )
Wheel size 8.5 JJ × 20 inset 45 8.5 JJ × 20 inset 45
Alignment
(Toe/Camber)
Test data - / - - / -
Standard value in 3~1 mm / -0°00' ± 45' in 4 ~ out 2 mm / -0°05' ± 30'
* Test data at HKS.


Parts List * It may be changed without prior notice.


Point
・The vehicle's height is set for ME51 before shipment; therefore, adjustment of the vehicle's height is required when installing this product to NE51 model.
 
・Improvement of a vehicle handling provides feeling as if the vehicle's weight off.
 
●Stock Parts Required for Installation
The following parts are required to reuse in order to install this products:
Rear spring lower seat, rear shock absorber upper mount, dust boots, and bump rubber.
 
 
 
 
 


[ CLOSE ]

 

 

HKS