MAX IV SP
GR SUPRA
GR SUPRA DB42

MAX IV SP

Code No. 80250-AT003

*Discontinued.

The sport model to have a comfortable drive even in the winding road.

 

 

The model in the photo is DB42.

 

 

Application

Engine B58
Model Year 19/05 - 
Remarks Note: Due to lowering the vehicle, a radar camera irradiated range becomes narrower and TTS (ToyotaSupraSafety) malfunction may occur with misalignment of the center.

Specification

  FRONT REAR
Damping force adjustment 30 steps 30 steps
Base valve - -
Height adjustable lower bracket
Upper mount Spherical bearing Spherical bearing
Inverted/Normal type Inverted Normal
Damper/Spring layout Coilover Separated
Spring rate change at factory
Damping force adjustment with wire -
Helper spring
(Spring rate N/mm)
○ ( 4.7 ) ○ ( 19.8 )
Ride Height mm
  Factory *2 Test data Adjustable range
High - Low *3
Drivable range
High - Low *4
FRONT Ride height *1 662 659 679 ~ 632 679 ~ 632
Against stock -25 -28 -8 ~ -55 -8 ~ -55
REAR Ride height *1 673 693 ~ 626 693 ~ 626
Against stock -25 -5 ~ -72 -5 ~ -72

*1. Height from road surface to fender arch.
*2. Height at factory is the data tested at HKS with the setting of Full Kit. (HKS' recommended setting.)
*3. Adjustable range (However, the lowest value may not be road legal.
Even within the adjustable range, car body, arm etc. may contact. In such case, it will be hard to drive.
Damper oil leakage or any other problems caused by low ride height setting from the factory setting will void the warranty of the product.)
*4. Drivable range that there is no contact of car body or arms etc. (However, change of tire/wheel size may cause a problem.)
Caution). Actual data depends on each vehicle.


Kit information

Spring of Full Kit

  F R
Spring rate N/mm(kgf/mm) 137 ( 14 ) 176 ( 18 )
Free height (mm) 150 200
Spring type 直巻※専用 Straight
Recommended range to change spring rate N/mm(kgf/mm) - -20 ( 2 )

Specification of damper

  F R
Damping force (Rebound/Damping)N* 1859 / 402 966 / 437
Default position of dial 15 15
Remaining damper stroke (Rebound/Damping)mm 43 / 46 57 / 57

* The value of the damping force is at piston speed of 0.1m/sec.

Setting data

  F R
Default Test Drivable limit
High *
Drivable limit
Low *
Default Test Drivable limit
High *
Drivable limit
Low *
Length of
case (mm)
279 289 264 324 341 291
Spring
Set length(mm)
189 192 184 200 - - - -
Length to ride hight
adjuster (mm)
26 23 41 0 50 62 22
Lever ratio 1.18 1.69(spg) , 1.20(dmp)

* Refer to the above explanation *3 of ride height information for drivable high and low limitations.



Test vehicle information

  F R
Vehicle weight kg 785.5 (780) 744 (740)
Tire size (Air pressure) kPa 255 / 35 - 19 ( 220 ) 275 / 35 - 19 ( 220 )
Wheel size 9.0 J × 19 10.0 J × 19
Alignment
(Toe/Camber)
Test data in 0.4 mm / -3°50' in 1.2 mm / -2°10'
Standard value in 3.1 mm ± 2.3 mm / -1°45' ± 0°30' in 2.7 mm ± 2.3 mm / -2°00' ± 0°25'

* Test data at HKS.


Parts List  * It may be changed without prior notice.

 


Point

Mr. Manabu Orido (also known as Mr. Supra) set a 1.682s faster time on racing track at Fuji International Speedway with only suspension upgrade.
This suspension utilized a conventional shock absorber rather than factory electronically controlled one and a vehicle is easier to understand and to control according to the driver's intention.
Using the high rate spring provides a smooth ride without too stiff feeling and at the same time helps to translate a feedback from tires.
Using HKS traditional inverted type at the front. To ensure the stroking amount and height adjustable range, HKS designed special outer cover.
Adjustment type pillow upper allows to adjust the camber angle.
The billet aluminum upper plate is used at the rear. This is for weight saving without losing the necessary strength.
The straight wound spring is used at both front and rear allowing to easily change spring rates.
Note: Error canceler is required due to removed factory Electronic Control Shock Absorber.
 
 
 



[ CLOSE ]

 

 

HKS